Bài viết Reyx Ul đã xuất hiện đầu tiên vào ngày CÔNG TY TNHH THIẾT BỊ KHOA HỌC KỸ THUẬT TRUNG HẢI.

Erosion is a very important step for both enamel and dentin surfaces.

Point

All direct, photocured restoration paste processes

Bonding procedure for indirect restorations when combined with RelyX ARC resin cement.

Reduces tooth root surface sensitivity.

Porcelain and composite repair.

Veneers combined with Rely X Veneer cement.

Preventive information for patients and dental staff

Scotchbond™ Universal Erosion Gel contains 32% phosphoric acid by weight. Contact with eyes or skin may cause burns. Wear suitable protective clothing, gloves and eye/face protection. In case of contact, rinse with plenty of water and see a doctor.

Preventive information for patients

This product contains substances that may cause allergic reactions from skin contact in some individuals. Avoid use of this product in patients with acrylate allergy. If prolonged contact with oral mucosa, rinse with plenty of water. If an allergic reaction occurs, seek medical attention as needed, discard the product if necessary, and discontinue future use of the product.

Precautionary information for dental staff

This product contains substances that may cause allergic reactions by skin contact in some individuals. To reduce the risk of allergic reactions, minimize exposure to these materials. In particular, avoid contact with products that are not covered. If skin contact occurs, wash skin with soap and water. Use of protective gloves and no-touch technique is recommended. Acrylates can penetrate regular gloves. If product comes into contact with gloves, remove and discard gloves, wash hands immediately with soap and water and then put on new gloves. If an allergic reaction occurs, seek medical attention if needed.

CONTACT ORDER NOW VIA PHONE NUMBER 091 972 1197 (Ms. Van Anh)

Harmful information

This is a flammable material.

Recommended use

Use 3M Vitrebond glass ionomer as a primer/light-curing base filling in deep sinus areas such as restoring sinuses I and II. If an exposed pulp area is present, use the minimum amount of calcium hydroxide followed by a Vitrebond primer/base. Adper Single Bond 2 adhesive will bond to the Vitrebond primer/substrate with or without acid treatment.

erode. Adper Single Bond 2 adhesive includes enamel and dentin erosion as part of the process. Surfaces are left damp after washing. Remove excess water from the surface with absorbent cotton. Adper Single Bond 2 adhesive is cured using a curing lamp. Lamp exposure times are guided when using 3M ESPE curing lamps or other lamps of equivalent intensity. Lamps should be tested for light intensity regularly using a reliable measurement system.

The air used for drying should not be contaminated with oil or water.

Sensitive

Some patients may experience temporary sensitivity after filling. The risk of sensitization can be minimized by the following measures:

Prepare teeth

Minimal tooth tissue removal.

Proper tooth isolation. Encourage the use of rubber dams. Use appropriate pulp protection. Use glass ionomer or resin-reinforced glass ionomer for priming/modified base fillings (Vitrebond liner/base fillings) in deep sinus areas.

Glue

It is not recommended to use steam to remove excess water after the etching step – absorb excess water with cotton balls or a small sponge.

Apply glue immediately after drying.

Recover

Place the filling material in layers, illuminating each layer separately. Appropriate lighting depends on the color of the filling material, the thickness of the material layer, and the duration of lighting.

Adjust your bite carefully. Check for excessive contact, especially lateral movement.

Corroded acid tube

Wear eye protection for patients and staff when using the dispenser.

Prepare the dispenser: Remove the cap from the corrosive acid tube and leave it on. Screw the blue disposable tip into the tube. Holding the acid tube away from the patient and surrounding staff, inject a small amount of etching gel onto paper or 2×2 gauze to ensure that the delivery tip is not clogged. If clogged, remove the dispenser tip and inject a small amount of erosive gel directly from the syringe. Discard any visible gel clumps, if any, at the top of the tube. Re-screw the tip and inject the etching gel again. If still clogged, remove the tip and replace it with a tip. Bend the tip to the desired angle. Bend the middle of the tip. Do not bend at the base of the tip as this may cause the tip to break.

Care of dispenser: Dispose of used and damaged tips. Twist on storage cap. Storing the gel tube with the tip in use or without the storage cap will dry out the gel and easily clog the dispenser tip. Replace the storage cap with a new tip for the next use.

If desired, pump the etching gel onto a piece of mixing paper and apply to the tooth with a toothbrush or other suitable tool.

If you want the etching gel to be more fluid, pump the gel into a mixing well and stir several times to increase flow.

Decontamination: Dispose of used tip. Cap the gel tube. See Storage and Use, Decontamination Instructions

User manual

Distribute Adper Single bond 2 glue

Press one edge of the cap to release the lock and pop the cap open, exposing the dispenser head

Squeeze the glue bottle to dispense the exact amount of glue you need into the disposable mixing well.

Once completed, close the lid until it is securely locked.

How to use

Guidelines for direct photocured restoration of enamel and dentin

Isolation: Rubber dams are the isolation method of choice.

Cavity preparation: Prepare the filling cavity with minimal invasiveness. Beveling the enamel edge of the filling cavity.

Erosion: applies enamel and dentin erosion. Wait 15 seconds. Rinse for 10 seconds. Soak up excess water with cotton balls or a small sponge. The surface will be slightly iridescent with no condensation.

Adhesive: Immediately after absorbing excess water, apply 2-3 successive coats of adhesive to the eroded enamel and dentin in 15 seconds with gentle movements using an applicator brush fully saturated with adhesive. Spray lightly for 5 seconds to evaporate the solvent. Shine the light for 10 seconds.

Place restoration material, cure, and complete: Refer to manufacturer’s instructions when placing restoration, cure, and complete restoration.

Instructions for porcelain veneers

Silane treatment: The porcelain surface should be etched with hydrofluoric acid in a dental laboratory. Apply RelyX Ceramic Primer to the veneer surface. Blow dry for 5 seconds.

Clean teeth that have been prepared for bonding and bonding using fluoride-free pumice powder. Rinse and blow dry.

Test veneers with RelyX™ Try-In Paste. After testing, isolate from adjacent teeth with the matrix.

Erosion: erosion of both enamel and dentin. Wait 15 seconds. Rinse for 10 seconds. Soak up excess water with a cotton ball or small sponge. The surface will be slightly iridescent without condensation. An additional 15 seconds of erosion may be applied when the tooth is not prepared with a bur. Remaining organic matter may also require additional etching time.

 

Adhesive: Immediately after absorbing excess water, apply 2-3 successive coats of adhesive to the eroded enamel and dentin in 15 seconds with gentle movements using an applicator brush fully saturated with adhesive. Spray lightly for 5 seconds to evaporate the solvent. No lighting.

Glue for veneer: apply a layer of glue to the veneer that has been treated with etching acid and silane. Dry thoroughly. No lights.

Bonding material for veneer: apply RelyX veneer cement on the veneer surface.

Attach veneer and light: attach veneer carefully. Remove excess cement from the veneer margin. Light each area of ​​the veneer according to the time recommended by the cement manufacturer. We recommend irradiating the gingival margin first, followed by the body and incisal margin. Avoid direct contact with the phototherapy lamp in the early stages.

Gluing instructions for composite and amalgam

Isolation: Rubber dams are the isolation method of choice.

Roughen the surface of existing materials: Roughen the surface of composite or amalgam using metal drills, diamonds or sandblasting techniques.

Erosion: Erosion to both enamel, dentin and existing restorations. Wait 15 seconds. Rinse for 10 seconds. Soak up excess water with cotton balls or a small sponge. The surface will be slightly iridescent without condensation.

Adhesive: Immediately after absorbing excess water, apply 2-3 coats of adhesive to enamel, dentin and existing restoration for 15 seconds with gentle movements using an applicator brush fully saturated with adhesive. Blow gently for 5 seconds to evaporate the solvent. Shine the light for 10 seconds.

Covering: In the case of amalgam, treat the metal surface with a suitable covering material. Apply the light according to the manufacturer’s instructions.

Placing the restoration: Refer to the manufacturer’s instructions when placing materials, lighting, and completing the restoration.

Instructions for repairing porcelain

Isolation: Rubber soles are the isolation method of choice

Preparation: Clean the surface in preparation for repair with a fluorinated pumice powder mixture. Rinse and dry thoroughly. Roughen the surface of existing metal or ceramic with a metal drill, diamond, or sandblasting. Carefully remove the thin layer of porcelain and shape the porcelain rim. Remove 1mm of the upper surface ceramic layer.

Etching: applying etching gel to the surface. Wait 15 seconds. Rinse for 10 seconds. Blow dry for 5 seconds.

Silane treatment of ceramic and metal: apply RelyX Ceramic Primer to the etched surface and blow dry.

Adhesive: apply 2 coats of Adper Single Bond 2 on ceramic or silane-treated metal. Blow dry gently for 5 seconds. Shine the light for 10 seconds.

Masking: To cover the metal before placing the final composite layer, cover the metal surface with a suitable masking agent. Apply the light according to the manufacturer’s instructions.

Place restoration, cure, and finish: Refer to manufacturer’s instructions when placing, curing, and completing restoration

Instructions for reducing tooth root surface sensitivity

Gently clean the tooth root surface with fluorinated pumice powder. Wash and dry.

Erosion: apply etching gel to the dentin. Wait 15 seconds. Rinse for 10 seconds. Pour off excess water with a cotton ball or small sponge. The surface will be slightly iridescent without condensation. 3. Glue: Immediately after absorbing water, apply 2-3 layers of glue to the eroded enamel and dentin for 15 seconds with a gentle sweeping motion. Blow gently for 5 seconds to evaporate the solvent. Shine the light for 10 seconds. Apply 2 more layers of glue. Blow dry gently for 5 seconds. Shine the light for 10 seconds.

Remove the oxygen-inhibited layer with a damp gauze.

Instructions on Amalgam bonding and indirect restoration (using RelyX ARC resin cement) Physical properties of restoration.

Today’s esthetics require restorations to be placed in the right place to maximize the durability of the restoration as well as the tooth tissue. There is a general perception that photocured adhesives cannot be used for indirect restorations. It is true that many conventional photocured adhesives have higher film thicknesses and cannot be used under fixed restorations. However, the Adper Single Bond 2 adhesive base is ethanol/water, has a low film thickness (about 10μm) and does not affect the attachment of indirect restorations. Note: Always be careful with any adhesive used under precision cast restorations as the added film thickness may cause less precise application of the restoration. Avoid getting adhesive on prepared teeth as this may affect the fit of any restoration.

Storage and Use

This product is intended for use at room temperature. If stored in a colder location, let product come to room temperature before use. The shelf life of glue at room temperature is 36 months. Ambient temperatures typically higher than 27°C/80°F may reduce shelf life. See the expiration date on the outside of the package.

Adper Single Bond 2 adhesive should be capped immediately after use to minimize evaporation.

Do not expose material to high temperatures or intense light.

Do not store product near products containing eugenol.

For cleaning, etching gel can be removed with water, while uncured adhesive can be cleaned with alcohol.

—————————————————-

TRUNG HAI Technology Equipment Co., Ltd. (Official distributor of 3M)

Address: No. 45-47, Street 2, Cityland Residential Area, Ward 10, Go Vap District

Phone: 028.224.2724

Hotline: 091 9721197 (Ms. Van Anh)

Website: http://thscientific.com/

CONTACT ORDER NOW VIA PHONE NUMBER 091 972 1197 (Ms. Van Anh)

Bài viết Instructions for using 3M™ ESPE™ Adper™ Single Bond 2 Dental Adhesive đã xuất hiện đầu tiên vào ngày CÔNG TY TNHH THIẾT BỊ KHOA HỌC KỸ THUẬT TRUNG HẢI.

Below are highlights of the event: Topic: Optimizing liquid composite applications in clinical practice

Time: April 26, 2024 | 19:00 – 21:30 (Vietnam time)

Platform: Zoom Meeting (Meeting ID: 936 2841 9262 Password: 263265 )

Expert: [ MSc.BS. Nattawit Niyomsujarit ]

Meeting ID: 936 2841 9262 / Password: 263265

Register: https://docs.google.com/forms/d/1S3CAtWvEp8O0I_22GTKN_1lpEjF_3c49axbGP6SSxvE/viewform?edit_requested=true

Conference content:

Discuss how to optimize clinical use of liquid composites to achieve maximum effectiveness.

Introducing 3M™ Filtek™ Supreme Flowable liquid composite product through a short video, with QR code for registering to receive 1G test samples.

3M™ Filtek™ Supreme Flowable liquid composite advertising materials including banner ad, video ad, brochure and sell sheet will be sent to customers via Zalo.

Note: Only registered doctors can participate. Please fill in accurate information in the Zoom software to be approved for the workshop. After the online workshop, participants will learn about: – Understanding the composition, physical and mechanical properties of liquid composites through analysis accumulation of research. – Share new applications of liquid composites through specific clinical cases.

Bài viết WEBINAR: OPTIMIZATION OF LIQUID COMPOSITE APPLICATION IN CLINICAL PRACTICE. đã xuất hiện đầu tiên vào ngày CÔNG TY TNHH THIẾT BỊ KHOA HỌC KỸ THUẬT TRUNG HẢI.

Time: 08:00 pm – 10:00 pm Vietnam

The development of modern technology has significantly influenced contemporary orthodontics, especially the emergence of self-ligating brackets in the early years of the twenty-first century. Although compared to traditional metal braces, forced braces still cause many problems controversy over the effectiveness of use: Dentists face many difficulties in manipulation and in choosing the right bracket system for each specific clinical case. However, we can not deny the outstanding advantages of braces self-ligating such as: low friction, reduced treatment time on dental chair…

Speaker:

Bài viết WEBINAR: Methods used Self-ligating brackets đã xuất hiện đầu tiên vào ngày CÔNG TY TNHH THIẾT BỊ KHOA HỌC KỸ THUẬT TRUNG HẢI.

This webinar will provide an overview of universal adhesives and explain why they are here to stay. The first universal adhesive, 3M™ Single Bond Universal, was launched in 2011 and introduced a new era of adhesive dentistry. Universal adhesives are designed to:

• Reliably deliver strong bonds
• Bond to many dental surfaces
• Work in total-etch, self-etch and selective-etch modes
• Work in both direct and indirect restorations
• Result in virtually no postoperative sensitivity

Learning Objectives:

You will learn about the benefits of incorporating universal adhesives into your practice, including:

• The freedom to do your best work no matter the etch technique
• A simple, streamlined system that lets you focus on providing the best patient care
• Fewer products to purchase and less inventory to manage
• Building a reputation for offering patients the latest innovations in dental adhesives

Speaker:

Dr Miryam Schuckar

Dr. Miryam Schuckar studied dentistry at the Bauru Dental School, University of São Paulo and obtained her master’s degree (M.Sc.) in Esthetic Dentistry. Her doctorate degree (Ph.D.) in Dentistry was obtained in 1995 from the Medical School of Hannover in Germany. She has long-term clinical and scientific experience as a dentist and lecturer for restorative dentistry and dental materials in Brazil and Germany, including participating in post-graduate programs and publishing many articles in important scientific magazines for dentistry. She has been featured as a speaker at international congresses including the International Association for Dental Research (IADR).

Dr. Schuckar also volunteers with Adveniat, German Doctors e.V., and other non-profits on a variety of social projects such as the development of a children’s education center in Brazilian favelas. She joined 3M Oral Care in June 2018 as a Global Scientific Affairs Manager with global responsibility for Dental Adhesives and Light Curing Devices and is based in Seefeld, Germany.

Get support from us: 0919 721 197 – Ms. Van Anh

Trung Hai is willing to receive your attention and your participation!

Bài viết WEBINAR: Why Choose Universal Adhesives đã xuất hiện đầu tiên vào ngày CÔNG TY TNHH THIẾT BỊ KHOA HỌC KỸ THUẬT TRUNG HẢI.

Course Objective:

The seminar helps you understand:

• Standards of occlusion
• Failure of prosthodontics caused by occlusion
• The role of articulator and selecting it in prosthodontics
• Treatment location with specific prosthodontic cases

Speaker:

Dr. Nguyen Vu Thuy Quynh

2013: graduated DDS at Ho Chi Minh University of Medicine and Pharmacy (HCM UMP)

2016: DIU Certificate (Bordeaux University – France) at HCM UMP, Vietnam – Occlusion and multi approaches

2017: graduated Resident, Master, and Specialist at HCM UMP

2018: Orthodontic certificate at HCM UMP, and continue to collect many basic and advanced certificates

2017 to present: practice in ArtDent Group Clinic

Webinar: Occlusion in Prosthodontic Treatment

–  Date: 29th Oct 2021 (Friday)

–  Time: 6:00 pm Jakarta, Bangkok, Hanoi

–  Participating fee: FREE

–  Hotline: 0919.721.197 – Vân Anh.

Trung Hai is willing to receive your attention and your participation!

Bài viết WEBINAR: Occlusion in Prosthodontic Treatment đã xuất hiện đầu tiên vào ngày CÔNG TY TNHH THIẾT BỊ KHOA HỌC KỸ THUẬT TRUNG HẢI.

Bài viết WEBINAR: Color in Dentistry and Shade Selection đã xuất hiện đầu tiên vào ngày CÔNG TY TNHH THIẾT BỊ KHOA HỌC KỸ THUẬT TRUNG HẢI.